24 Results
View results:
Sort by:
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Strength of Weld-Affected Zone for Aluminum
How do I consider the strength of weld-affected zone for aluminum?
Parallel Calculations
When analyzing the combinations using the geometric linear method, it seems that the parallel calculation works. However, when I change the method to the second-order analysis, it seems that the solver calculates the combinations one by one.
Consideration of Heat Affected Zone for Aluminum
Is it possible to consider the reduction of strength in the heat affected zone (HAZ) in the RF‑/ALUMINUM add-on module?
Question
I am trying to design an open, unsymmetric aluminum cross-section in RF‑/ALUMINUM and I am get the warning "Non-designable - 1022) General cross-section — Check of stability is not available". What is the reason?
Effective Length Factors for Aluminum and Steel Design
Are effective length factors determined automatically from a model in the add-on modules for aluminum and steel design, or do I have to make adjustments?
Question
I have performed a buckling analysis in RF‑ALUMINUM. Where can I find the parameters used for the design in the add-on module?
Question
It is not possible to design a SHAPE‑THIN cross-section due to invalid symmetry. What is the cause and how can I fix it?
Question
The calculation of a result combination in STEEL EC3 or ALUMINUM takes a very long time. What might be the cause, and how can I improve the performance?
Question
Which modules can be accessed via the COM interfaces RS‑COM and RF‑COM?
Question
I get an implausible result with the expression "1.#J" in the RF‑/ALUMINUM add-on module.
How can I fix this?
Question
Why does my calculation in the RF‑/ALUMINUM add‑on module take so long?
Question
How can I change the allowable thickness ranges for the material in RF‑/ALUMINUM or RF‑/STEEL EC3?
Question
When trying to calculate a material from the "Aluminum" category in the RF‑/EL‑PL add-on module, I get an error message. What is the reason for this?
Question
Can I also perform fatigue design with Dlubal programs?
- 002628
- ALUMINUM 8
- ALUMINUM ADM 8
-
- RF-ALUMINUM 5
- RF-ALUMINUM ADM 5
- RF-STEEL 5
- RF-STEEL AISC 5
- RF-STEEL AS 5
- RF-STEEL BS 5
- RF-STEEL CSA 5
- RF-STEEL EC3 5
- RF-STEEL Fatigue Members 5
- RF-STEEL NTC-DF 5
- RF-STEEL SIA 5
- STEEL 8
- STEEL AISC 8
- STEEL AS 8
- STEEL BS 8
- STEEL CSA 8
- STEEL EC3 8
- STEEL Fatigue Members 8
- STEEL SIA 8
- KAPPA 8
- RF-KAPPA 5
- LTB 8
- RF-LTB 5
- Steel Structures
- Stress Analysis
- Stability Analysis